Glass-steel cool water tower standard design conditions and performance analysis glass steel cool water tower is a common refrigeration equipment, it has a wide range of applications in a variety of industries. Use high-pressure water to wash the soil on the sink of the cooling film and cooling tower, and drain the water through its drains. Cooling tower water turbidity is not greater than 10 mg/L, when running, according to the water quality situation, consider regular discharge or increase water quality stability treatment. The method of daily maintenance of the glass-and-steel cooling tower regularly cleans the moss, mud and debris in the glass-steel cooling tower with the sink, at least once a year in spring and autumn. How can the glass-steel cool water tower do a good job of anti-freeze fiberglass cool water tower cold winter operation and flow and half a large cooling tower, can be the cooling tower under the preset pool or water box, glass-steel cool water tower back water can flow directly into the water box or pool, reduce the possibility of the glass-steel cool water tower itself, the possibility of freezing; Long and interrupted operation must increase electricity on the pipeline to avoid freezing and cracking, if the reverse round glass and steel cool water tower, cold winter operation can be the end of the glass-steel cold water tarding pipe or surrounding lotus head congestion, as far as possible to prevent the spill outside the life cycle water; Energy saving: make full use of the return pressure of the circulating water system to convert to mechanical energy, external water turbine to replace the motor drive, to reach 100% energy saving. Do not come into contact with the inner circulating water, but only through the cooling tower copper tube table cooler for heat exchange heat dissipation. 0 Large Synth quiz records the type and quantity of all chemicals used to disinfect the measurement and results of FRC or FRB and pH values. Closed cooling tower is a kind of deformation and development of traditional cooling tower. This cooling tower device takes up a smaller space range, but the same amount of work can be done within a smaller space range, with the same cooling effect.
Second, the glass-steel cooling tower equipment in the energy-saving and environmental protection advantages are more obvious, first of all, compared with the previous equipment on the power savings more obvious, while the noise issued at work is less, the equipment has advanced noise reduction design, the equipment is also a lot smaller sound. The water in the reservoir at the bottom of the tower is pumped by a circulating pump and sprayed evenly outside the tube. The reason swhat for the cheap main products: Suzhou cooling tower Hangzhou cooling tower Wujiang cooling tower Jiaxing cold water tower specification table 10 brand cooling tower cleaning step 3 requires features using skill mechanical cleaning: off and isolated water circulation pump. In this cooling mode, the motor is operated according to the water temperature, via automatic control. Safety: fundamentally eliminate the motor, electrical control and leakage burn damage damage failure, for the safe and continuous operation provides a guarantee, can be safe lying in any environment required explosion-proof environment. Glass-steel cool water tower sink electric heater, and set the temperature control action treatment method, set up the heat eras, if the glass-steel cool water tower filler, wind window surrounding the frozen can make the fan turn back, the addition of steam pipe in accordance with the prescribed time limit ice to prevent freezing. Regularly check and eliminate leaks, breaks, breaks and other defects in the dingnel. The filler material is modified to temperature-resistant hard PVC (PVC), or high-temperature polypropylene (PP). It also checks that the wiring of the motor is correct. In order to give you a better understanding of this product, here's a brief overview of the standard design conditions and performance of the next product.
Check how tight the belt is in the belt drive unit of the glass-and-steel cooling tower. Regularly and regularly inspect and correct the splash ingress so that the water flow of the nozzle can be directed vertically at the center of the splash disk, with a median of more than 90%. Cooling tower equipment structure and energy-saving application 7 equipment composition: automatic rotating atomized cooling tower by the water main, automatic rotating atomist, housing, water collector, fan, motor, wind feed window, water collection disk (water tank), tube, bracket, escalator and other components. Note: The above is for the single tower to do the structural description, for different processing volume, can be composed of two towers, multi-tower structure. If necessary, spot sodium sulphate in the water. Third, the corrosion resistance of the equipment is better than ever, and the service life will become longer. This glass-steel cool water tower standard design conditions: dry ball temperature 35 degrees C, wet bulb temperature 28 degrees C, atmospheric pressure 99400Pa, water inlet temperature of 42 degrees C, temperature 32 degrees C. When the production of algae in circulating water, the impact chlorine can be removed. A good helper for the treatment of industrial waste heat - glass-steel cool water tower glass-steel cool water tower is a structure used by the power plant for cold water, is the use of blowing in the wind and water from the water sprinkled down to form convection, the heat object is drained, a small amount of water evaporated in the convection, took away the corresponding evaporation potential heat. The filler cooling tower is the cooling circulating cooling water is evenly distributed on the filler, the shaft fan installed at the top of the tower by motor drive suction suction into the tower, the cold air and hot water in the filling surface for the transfer of heat, to reduce the water temperature. Does not come into contact with process fluid hot water or refrigerant and extra-tube air, becoming a closed cooling tower that enhances heat transfer by spraying water.
Can be combined into a variety of water cooling tower group, the structure itself gives the product excellent low noise performance, vertical installation height is low, suitable for some special places. The amount of chlorine can be controlled in the return water main tube with residual chlorine of 0.5 to 0 mg/L, and the time is 4 to 6 hours. Thus reducing the temperature of a machine, notably unique is: no electricity, fan semi-automatic rotation, saving 100, water saving 80. This cooling tower, water and air contact area is small, filler shading air resistance, noise, relatively large energy consumption, high failure rate, large maintenance, high maintenance costs, short service life, high water quality requirements, cooling effect is not ideal. Closed cooling towers are suitable for a variety of cooling systems that require high recycled water quality and are used in power, chemical, steel, food and many industries. Check whether the fan's rotation is flexible and so on. Nozzles and splash dishes should be cleaned or replaced in a timely manner if they are blocked or damaged. How to operate: Automatic rotating atomized cooling tower is by circulating cooling water and cold, dry air heat conduction and the evaporation of circulating cooling water to take away the gasification potential heat and achieve the goal of reducing water temperature. The area analysis process checks all water contact areas of sediment, silt and scale. This is very much in line with the use of the unit's pursuit of long-term interests.
Cooling tower operation should pay attention to the matter slower tower operation should pay attention to the matter: the gearbox should often check the oil label oil level, oil recommended with 22 to 28 double-curve gear oil or 90 to 120 industrial gear oil, summer with a large viscosity oil. In industrial production will often leave a local waste heat, these waste heat only after a certain amount of device cooling in this, the ability to follow the implementation of the office, if you do not pay attention to waste heat disposal, the mechanical operation of the germination temperature will be higher and higher, whether the machine is still inside the components, will be a major damage. Clean cooling tower water contact area, including basins, cooling tower factory pool, cooling tower factory filling nozzles and accessories. The low noise device is equipped with noise reduction device sesame in and out of the air port, so that the same level of equipment effectivenoise reduction up to 5dB. When the ceramic nozzle and splash ingress have scale in the disk and affect the performance, it should be cleaned with 10% hydrochloric acid solution under the guidance of the chemical sub-field. The energy-saving features of the cooling tower are: no electricity, automatic rotation of the fan, 100% saving electricity, 80% water saving. The glass-and-steel cooling tower will completely replace the old equipment; in recent years, while the replacement of large-scale equipment has not been as rapid as the electronic information industry, the impact of each replacement generation is far greater than that of other industries. Cooling towers have been used in the industrial field cooling towers work by changing heat with the surrounding air to cool the water. The main purpose of the cooling tower is to improve the heat exchange efficiency of water. The rate of lift mainly from the large heat exchange area, increase water in the process of falling time, rapid air flow, these aspects of the start. With the continuous development of materials, processes, technology, cooling towers will become smaller and smaller, quieter, but also adapt to more environment seis! Cooling tower glass and steel parts: from temperature-resistant, aging-resistant, water-resistant polyester resin, the surface of the rubber resin, with anti-aging, corrosion-resistant, bright and clean, non-leg color and so on. The circulating cooling water with a certain pressure enters the cooling tower through the inlet pipe, under the act of the translactof of the nebulizer, is atomized to the direction of the fog vapor with a diameter of 0.1mm towards the top of the tower, and the resulting counter-thrust drives the automatic rotation device to rotate, causing the atomized water to fill the entire tower body. On the other hand, compared with the air-cooled heat exchanger, the evaporative cooling tower utilizes the evaporation latent heat of the water under the tube, which makes the air side heat transfer significantly enhanced, and also has obvious advantages.
Fan: According to user requirements can be equipped with aluminum alloy and fiberglass fan one, both have a tower machine matching reasonable, large air volume, low noise and other characteristics of the motor: the use of outdoor cooling tower special motor, gearbox. The axial fan mounted on the top of the tower rotates and forces the cold and dry air of the surrounding environment through the inlet window into the cooling tower to transmit mass and heat with the circulating cooling water. Closed cooling tower classification: according to the direction of water flow and wind direction can be divided into: reverse-flow closed cooling tower, cross-flow closed cooling tower. Using a grooved water system, the water is uniform and not easily clogged. Reasonable use of adjustment hydraulic distribution measures, such as if necessary can change the nozzle diameter, adjust the height of the water tank, install the water tank adjustment gate. Cooling tower is an energy-saving product, is a recycling water refrigeration industry technology. Almost every change can cause a huge change in the entire industry, this is not only the promotion of technical strength, but also the overall strength and the industry pattern of great changes, the application of the glass-steel cooling tower belongs to such an industry area, so the cooling tower equipment change, but also exists such characteristics. Drain the oil and change the oil after 500 hours at a time. The glass-steel cool water tower is a special facility for the disposal of industrial waste heat, it is through direct contact between water and air for heat exchange, in the power of cooling fan, the cooler air and water in the filler heat exchange, in order to achieve the goal of reducing water temperature. How much ah what to do if possible, clean the cooling tower /evaporative condenser in the contact area.
Fan: According to user requirements can be equipped with aluminum alloy and fiberglass fan one, both have a tower machine matching reasonable, large air volume, low noise and other characteristics of the motor: the use of outdoor cooling tower special motor, gearbox. The axial fan mounted on the top of the tower rotates and forces the cold and dry air of the surrounding environment through the inlet window into the cooling tower to transmit mass and heat with the circulating cooling water. Closed cooling tower classification: according to the direction of water flow and wind direction can be divided into: reverse-flow closed cooling tower, cross-flow closed cooling tower. Using a grooved water system, the water is uniform and not easily clogged. Reasonable use of adjustment hydraulic distribution measures, such as if necessary can change the nozzle diameter, adjust the height of the water tank, install the water tank adjustment gate. Cooling tower is an energy-saving product, is a recycling water refrigeration industry technology. Almost every change can cause a huge change in the entire industry, this is not only the promotion of technical strength, but also the overall strength and the industry pattern of great changes, the application of the glass-steel cooling tower belongs to such an industry area, so the cooling tower equipment change, but also exists such characteristics. Drain the oil and change the oil after 500 hours at a time. The glass-steel cool water tower is a special facility for the disposal of industrial waste heat, it is through direct contact between water and air for heat exchange, in the power of cooling fan, the cooler air and water in the filler heat exchange, in order to achieve the goal of reducing water temperature. How much ah what to do if possible, clean the cooling tower /evaporative condenser in the contact area. ...
As can be seen from the above working process, the circulating cooling water has three processes of rising, suspending and falling in the cooling tower. The structural features of the cooling tower in order to save energy, large fiberglass cooling water tower with natural ventilation cooling tower, it is composed of ventilation cylinder, human column, ring base, water pumping device and tower core material. The variety process indicates that the re-installed components and hoses are clean with water. According to the heat exchanger material can be divided into: copper pipe closed cooling tower, stainless steel tube closed cooling tower, carbon steel pipe closed cooling tower, titanium pipe closed cooling tower, aluminum tube closed cooling tower. The burning point of the glass and steel is relatively low, if there is a source of fire, it is easy to cause great damage. Considered appropriate and use air-cooled and spraywater evaporation heat absorption two-cooling form, cooling medium fully closed cycle. Keep the circulating ditch filter mesh complete and clean, clean when dirty clogging, when rust damage in time to repair or more. Water distribution system: according to user requirements, the use of rotating water or pipe-type water distribution system. Meet the requirements and then start, start in order, from low speed to high speed. If you also want to learn more, stay tuned for the next time.